濟南瓷磚粘結劑使用步驟：

Steps for using Jinan ceramic tile adhesive:

基層處理→瓷磚粘結劑混合攪拌→批刮瓷磚粘結劑→鋪貼瓷磚

Basic treatment → Mixing and stirring of ceramic tile adhesive → Batch scraping of ceramic tile adhesive → Laying of ceramic tiles

1、基層清理待貼磚基層應平整、干凈、結實、無粉塵、油脂等污物及其它松散物,清理干凈瓷磚背面的脫模劑、脫膜粉備用

1. The base layer to be tiled should be flat, clean, sturdy, and free of dust, grease, and other loose materials. Clean the release agent and release powder on the back of the ceramic tile for backup

2、瓷磚粘結劑混合攪拌按照水粉比1:4（1包20kg瓷磚粘結劑加5kg水）的比例先在攪拌桶內加入適量的水，然后將瓷磚粘結劑倒入攪拌桶內，邊加入邊用電動攪拌器攪拌，至無粉團、結塊為止。拌勻后需靜置5分鐘，再攪拌1分鐘即可使用

2. Mix and stir the ceramic tile adhesive in a water to powder ratio of 1:4 (1 pack of 20kg ceramic tile adhesive with 5kg of water). First, add an appropriate amount of water to the mixing bucket, and then pour the ceramic tile adhesive into the mixing bucket. Use an electric mixer to stir while adding until there are no powder lumps or clumps. After mixing well, let it stand for 5 minutes and stir for another 1 minute to use

3、批刮瓷磚粘結劑貼磚前，基面適量灑水潤濕，用齒形刮板將膠漿涂于待貼磚基面，然后握住齒形刮板使其齒邊與基面成45°角，將膠漿層梳理成均勻條狀；同時將膠漿均勻涂布于瓷磚背面

3. Before applying ceramic tile adhesive for tiling, sprinkle an appropriate amount of water on the base surface to moisten it. Use a toothed scraper to apply the adhesive to the base surface to be applied, and then hold the toothed scraper to make its tooth edge form a 45 ° angle with the base surface. Sort out the adhesive layer into a uniform strip; Simultaneously apply the adhesive evenly to the back of the ceramic tile

4、鋪貼瓷磚將已批刮瓷磚粘結劑的瓷磚鋪壓到貼磚基層，在垂直于梳理方向輕微搓動排除磚內空氣，用橡皮錘敲擊瓷磚表面至瓷磚四周出漿，確保瓷磚背面瓷磚粘結劑已均勻涂漿。

4. Paving tiles: Press the tiles that have already been scratched with tile adhesive onto the base layer of the tiles. Gently rub the tiles in a direction perpendicular to the combing direction to remove air inside the tiles. Use a rubber hammer to tap the surface of the tiles until grout is released around them, ensuring that the tile adhesive on the back of the tiles has been evenly applied.

薄貼法的基本特征就是，用的瓷磚粘合劑及齒型刮刀，在施工的基層先將瓷磚粘合劑梳刮成條紋狀，然后再鋪貼瓷磚。

The basic feature of the thin tiling method is to use professional tile adhesives and toothed scrapers to comb and scrape the tile adhesive into stripes on the construction base, and then lay the tiles.

薄貼法使用的瓷磚粘合劑厚度一般只有3-5mm，厚度比傳統的厚貼法會薄上許多。

The thickness of the ceramic tile adhesive used in the thin pasting method is generally only 3-5mm, which is much thinner than the traditional thick pasting method.

瓷磚厚貼法

Thick tiling method

瓷磚厚貼法是為傳統的裝貼方式，采用傳統水泥、沙，施工現場加水調配，厚抹灰粘貼方法，水泥砂漿的厚度一般會在15-20mm。更多相關事項就來我們網站http://m.zzmdwxsh.com咨詢吧！

The thick tiling method for ceramic tiles is a traditional installation method that uses traditional cement and sand, mixed with water on the construction site, and thick plastering. The thickness of cement mortar is generally 15-20mm. For more related matters, come to our website http://m.zzmdwxsh.com Consult!