I. Installation Technology of Gypsum Line

　　1. 清洗:安裝抹灰線前，應清理安裝現場的膩子粉和灰塵。有些難以清潔的物質可以用水輥涂上一層水，然后用鏟子清理干凈。這樣可以保證石膏線安裝更加牢固，避免石膏線在以后出現脫落的現象。

　　1. Cleaning: Putty powder and dust should be cleaned up before plastering line is installed. Some substances that are difficult to clean can be coated with water rollers and cleaned with shovels. This can ensure that the installation of gypsum line is more solid, and avoid the phenomenon of gypsum line falling off in the future.

　　2. 油漆墨線:清潔灰塵后，將墨線與墨桶一起涂在墻面上。但在墻面頂角處用一段線條用力輕輕畫出，量出墻體的長度，將決定石膏線的長度和寬度。

　　2. Paint ink line: After cleaning the dust, paint the ink line and ink bucket on the wall together. But the length and width of the gypsum line will be determined by measuring the length of the wall by gently drawing a line at the top corner of the wall.

　　3.石膏線切割:確定石膏線長度后，切割石膏線。再剪兩端，就可以把膏藥線放上去，按45度已婚女性剪兩端。

　　3. Gypsum wire cutting: After determining the length of the gypsum wire, cut the gypsum wire. Cut both ends, you can put the plaster line on, according to 45 degrees married women cut both ends.

　　4. 石膏粉治療:石膏粉和水以一定比例混合,均勻涂抹它兩邊的石膏線條,然后使石膏行充裕的下緣的位置墨,拿了幾分鐘,然后用混合石膏粉填充頭部。

　　4. Gypsum powder treatment: mix gypsum powder and water in a certain proportion, evenly smear the gypsum lines on both sides of it, then make the gypsum line abundant lower edge position ink, take a few minutes, and then fill the head with mixed gypsum powder.

　　二世。注意事項

　　King II. Matters needing attention

　　1. 基本治療。石膏線施工前應清理基層，墻面應平整，無凸凹部位。墻頂角的地方，會吹膩子兩次。這將防止石膏線脫落。

　　1. Basic treatment. Before the construction of gypsum line, the base should be cleaned up, the wall surface should be flat and there should be no convex and concave parts. Putty will be blown twice at the top corner of the wall. This will prevent the gypsum line from falling off.

　　2. 石膏線在施工中，要從正面開始，這樣才能保證石膏線的正節(jié)理部分更少，使石膏線的整體效果看起來更流暢。將不足一半的關節(jié)或需要的關節(jié)放置在未標記的區(qū)域。

　　2. In the construction of gypsum line, it is necessary to start from the front, so as to ensure that there are fewer normal joints of gypsum line and make the overall effect of gypsum line look smoother. Place less than half of the joints or required joints in unmarked areas.

　　3.由于石膏的凝結時間相對較短，所以在安裝石膏線時，需要快速粘貼和調整，并迅速補上有缺陷的部分。打石膏前一定要用水清洗邊緣。

　　3. Because the setting time of gypsum is relatively short, it is necessary to paste and adjust quickly when installing gypsum line, and fill the defective parts quickly. Clean the edges with water before plastering.

　　4. 在石膏線的接縫處，必須刮掉石膏后才能進行對接。對接時應注意花紋與紋理的匹配，高度一致。使石膏線整體呈直線，下部應采用石膏墊直，以免石膏出現斷線的問題。石膏線安裝后，應及時用清水清洗干凈，以免石膏凝固，污漬無法清洗，從而影響石膏線的整體美觀程度。

　　4. At the joint of the gypsum thread, the gypsum must be scraped off before the joint can be made. When docking, attention should be paid to the matching of pattern and texture, which is highly consistent. In order to make the gypsum line straight as a whole, the lower part should be upright with gypsum pad in order to avoid the problem of broken line in gypsum. After installation of gypsum line, it should be cleaned with clear water in time to avoid gypsum solidification and stain can not be cleaned, thus affecting the overall aesthetic level of gypsum line.

　　5. 石膏線修復過程中，將石膏線粘貼后，對石膏線接縫部位進行修復，以稀釋石膏線接縫部位。對墻面進行修復，保證石膏線出墻的部位寬度一致。

　　5. In the process of repairing the gypsum thread, after pasting the gypsum thread, the joint of the gypsum thread is repaired to dilute the joint of the gypsum thread. Repair the wall surface to ensure that the width of the gypsum line out of the wall is the same.