The decoration of the wall is a very important step in the decoration of a family. There are a lot of stresses on the wall, such as polishing and leveling. Today, the editor of fangtianxia will solve the problem of the wall decoration for you. Please come to see the mortar plastering construction technology with me. The editor summarizes a series of problems about the wall according to the experience of many decoration masters Decoration related information, come and have a look.

1、基層處理

1. Basic treatment

①基層清理：清除干凈、灑水潤濕。其中：混凝土表面潤濕后涂刷1：1水泥砂漿(加適量膠粘劑);加氣混凝土應在濕潤后，抹強度不小于M5的水泥混合砂漿。

① Base cleaning: clean and wet with water. Among them: 1:1 cement mortar (with appropriate amount of adhesive) shall be painted on the surface of concrete after wetting; cement mixed mortar with strength not less than M5 shall be painted on aerated concrete after wetting.

②加強措施：當抹灰總厚度大于或等于35mm時，應采取加強措施。

② Strengthening measures: when the total thickness of plastering is greater than or equal to 35mm, strengthening measures shall be taken.

③細部處理：室內墻面、柱面和門洞口的陽角做法，設計無要求時，應采用1：2水泥砂漿做暗護角，其高度不應低于2m，每側寬度不應小于50mm.

③ Detail treatment: for the external corners of indoor walls, columns and door openings, 1:2 cement mortar shall be used as concealed corner protection when there is no design requirement, and its height shall not be less than 2m, and the width of each side shall not be less than 50mm

2、分層抹灰

2. Layered plastering

分為底層、中層及面層。其中，水泥砂漿不得抹在石灰砂漿層上;罩面石膏灰不得抹在水泥砂漿層上。

It is divided into bottom layer, middle layer and surface layer. Among them, the cement mortar shall not be plastered on the lime mortar layer; the overlay gypsum shall not be plastered on the cement mortar layer.

3、控制厚度

3. Control thickness

通常抹灰構造各層厚度宜為5～7mm，抹石灰砂漿和水泥混合砂漿時宜為7～9mm.當設計無要求時，抹灰層的平均總厚度：內墻(普通20mm，25)，外墻(20)，石墻(35)。

Generally, the thickness of each layer of plastering structure should be 5-7mm, and that of lime mortar and cement mixed mortar should be 7-9mm. When there is no design requirement, the average total thickness of plastering layer is: internal wall (common 20mm, 25), external wall (20), stone wall (35).

4、設置分格縫

4. Setting the dividing seam

5、保護成品

5. Protection of finished products

各種砂漿抹灰層，在凝結前應防止快干、水沖、撞擊、振動和受凍。水泥砂漿抹灰層應在濕潤條件下養護，一般應在抹灰24h后進行養護

All kinds of mortar plastering layers shall be protected from quick drying, water flushing, impact, vibration and freezing before setting. The cement mortar plastering layer should be cured under wet conditions, generally after 24 hours of plastering